目前分類：Cisco (12)

瀏覽方式： 標題列表 簡短摘要

class-map match-all mgmt
 match access-group name mgmt

(繼續閱讀...)

里歐 發表在 痞客邦 留言(0) 人氣()

▲top

Example of Password Recovery Procedure
WebPage : http://www.cisco.com/en/US/products/hw/routers/ps221/products_password_recovery09186a0080094773.shtml

This section provides an example of the password recovery procedure. This example was created with a Cisco 2600 Series Router. Even if you do not use a Cisco 2600 Series Router, this output provides an example of what you should experience on your product.

(繼續閱讀...)

里歐 發表在 痞客邦 留言(0) 人氣()

▲top

WebPage：http://www.cisco.com/en/US/products/hw/routers/ps133/products_tech_note09186a008022493f.shtml

Configuration Register Setting Router Behavior
0x102 Ignores break
9600 console baud
0x1202 1200 baud rate
0x2101 Boots into bootstrap
Ignores break
Boots into ROM if initial boot fails
9600 console baud rate
0x2102 Ignores break
Boots into ROM if initial boot fails
9600 console baud rate default value for most platforms
0x2120 Boots into ROMmon
19200 console speed
0x2122 Ignores break
Boots into ROM if initial boot fails
19200 console baud rate
0x2124 NetBoot
Ignores break
Boots into ROM if initial boot fails
19200 console speed
0x2142 Ignores break
Boots into ROM if initial boot fails
9600 console baud rate
Ignores the contents of Non-Volatile RAM (NVRAM) (ignores configuration)
0x2902 Ignores break
Boots into ROM if initial boot fails
4800 console baud rate
0x2922 Ignores break
Boots into ROM if initial boot fails
38400 console baud rate
0x3122 Ignores break
Boots into ROM if initial boot fails
57600 console baud rate
0x3902 Ignores break
Boots into ROM if initial boot fails
2400 console baud rate
0x3922 Ignores break
Boots into ROM if initial boot fails
115200 console baud rate
(繼續閱讀...)

里歐 發表在 痞客邦 留言(0) 人氣()

▲top
===============================================================
Configure Cisco switch telnet login and password
(繼續閱讀...)

里歐 發表在 痞客邦 留言(0) 人氣()

▲top
This documents the procedure for performing a password recovery on a Cisco 2950 switch (and probably other models, as well).

(繼續閱讀...)

里歐 發表在 痞客邦 留言(0) 人氣()

▲top

參考一下文章：

(繼續閱讀...)

里歐 發表在 痞客邦 留言(0) 人氣()

▲top
Enabling Aggressive UDLD on SW1 and SW2
 
(繼續閱讀...)

里歐 發表在 痞客邦 留言(0) 人氣()

▲top
fig11
Creating the Channel Group on SW1
(繼續閱讀...)

里歐 發表在 痞客邦 留言(0) 人氣()

▲top
SW4#config t
Enter configuration commands, one per line. End with CNTL/Z.
(繼續閱讀...)

里歐 發表在 痞客邦 留言(0) 人氣()

▲top

RSM1#show interface vlan130
Vlan130 is up, line protocol is up

(繼續閱讀...)

里歐 發表在 痞客邦 留言(0) 人氣()

▲top

Example Configuring a SVI for VLAN 130 on the RSM of SW3

RSM1#config t
Enter configuration commands, one per line. End with CNTL/Z.
RSM1(config)#int vlan130
RSM1(config-if)#ip address 172.16.196.1 255.255.255.0
RSM1(config-if)#end
RSM1#
(繼續閱讀...)

里歐 發表在 痞客邦 留言(0) 人氣()

▲top
SW3> (enable) show mod 4
Mod Module-Name     Ports Module-Type      Model  Serial-Num Status
(繼續閱讀...)

里歐 發表在 痞客邦 留言(0) 人氣()

▲top